Magnetically park your HVE and saliva ejector, chairside.
Designed by dentists, engineered for precision.
(Compatible with A-dec 300 and 500 series units)
-
Fits A-dec setups
A-dec 300 and 500, more systems coming.
-
30-day returns, 90-day warranty
Manufacturer defects replaced free.
-
Patent pending
Outfitted 800+ dental practices since Oct 2025.
Wholesale pricing for large practices and organizations: contact us. We regularly work with distributors as well.
Products
Outfit the full operatory
Park both valves: the Large HVE adapter paired with a Small saliva ejector adapter. Choose the Small by hose: smooth is 7.5mm, ribbed is 10.5mm.
Not sure which size fits your unit? Check the sizing guide before you order.
Shop all adapters
New production run
Updated adapters, now shipping
- A firmer fit in the hanger holder, with a textured grip on the tray mount
- The same 1/4 inch magnet in every size, installed in the tray mount
- Consistent polarity: any wand ring parks on any tray mount
- Nickel-coated magnets that passed 96 hours of salt spray testing, and 304 stainless steel screws
Fit
Will it fit your operatory?
Currently our patent-pending adapters fit A-dec 300 and 500 series suction systems only. Coming soon: a universal design in development to fit more systems.
Parking the HVE?
The Large adapter fits the A-dec standard HVE valve, with standard 1/2 inch tubing and large-bore 16mm tubing.
Shop the Large adapter
Parking the saliva ejector?
The Small adapter fits the A-dec standard saliva ejector valve. Available for 7.5mm (standard) and 10.5mm (high-volume) hoses.
Shop the Small adapters Not sure which size? Measure the hose inner diameter. A 7.5mm hose
is smooth. A 10.5mm hose is ribbed. Still unsure? Contact us
with a photo and we will confirm the fit before you order.
Full sizing guide These accessories are intended for professional dental and laboratory use only. No patient treatment or clinical services are provided through this site.
Installation
Installs in minutes
No new equipment and no change to your plumbing. Two parts retrofit onto the setup you already have.
-
Swap the tailpiece
The valve pulls off the tailpiece and the tailpiece pulls out of the hose. Press the holder ring into the hose. A water based lubricant helps.
-
Mount the tray
Loosen the set screw on the bottom of the tray mount. Slide the tray mount into your existing hanger holder, hold it steady, and tighten the set screw until firm. If it still slips, clean the inside of the hanger holder and the tray mount with light-grit sandpaper. For extra grip, add a wrap of Teflon tape around the tray mount.
-
Park and go
The magnet parks your suction tip chairside, within reach. It lifts off in an instant.
Full installation walkthrough, about 2 minutes.
Full installation guideGood to know
Common questions
Installation takes a few minutes and no new equipment: the valve pulls off the tailpiece, the tailpiece pulls out of the hose, and the wand ring presses into the hose (a water based lubricant helps). Then place the Tray Mount into the hanger holder and tighten the bottom screw.
The full step-by-step walkthrough, including the two minute video, is on the installation page.
Our product uses a neodymium rare earth magnet, which is strong but compact. While magnets like this can pose a theoretical risk of interference with pacemakers and implantable cardioverter-defibrillators (ICDs), the likelihood of interference during routine dental procedures is considered very low, especially with modern shielding in today's devices.
That said, magnets can temporarily alter device behavior:
- A magnet placed over a pacemaker can force it into a fixed pacing mode, overriding the patient's programmed settings.
- A magnet placed over an ICD can suspend its shock therapy function, though it does not affect pacing.
As a safety protocol, we recommend dental providers ask patients whether they have a pacemaker or ICD and keep the suction and magnetized components at least 6 inches away from such devices at all times.
This guidance is based on standard medical device recommendations and reviewed by a board-certified cardiologist.
Our product is patent pending.
We've officially filed a patent application with the United States Patent and Trademark Office (USPTO) to protect our innovative design.
This means the product is currently under review and not yet issued a full patent, but the intellectual property is actively protected.
Yes. Every adapter, Large and Small, ships with the same 1/4 inch magnet already installed in the tray mount. There is no separate magnet or washer to fit.
Park it chairside.
Retrofit your existing A-dec setup. No new equipment, no change to your workflow.
Shop the adapters30-day returns · 90-day warranty · Patent pending